產品中心您當前的位置:首頁 > 產品中心 > 愛斯佩克ESPEC環境試驗箱 > 高低溫濕熱試驗箱 > 愛斯佩克高低溫試驗箱ESPEC ARL-0680-AE

基礎信息Product information

產品名稱:愛斯佩克高低溫試驗箱ESPEC ARL-0680-AE

產品型號:

更新時間:2017-04-16

產品簡介:

愛斯佩克高低溫試驗箱ESPEC ARL-0680-AE系列產品適用標準:GB/T2423.3 / IEC60068-2-78、GB/T2423.4 / IEC60068-2-30、GB/T2423.34 / IEC60068-2-38、GB/T2423.22 / IEC60068-2-14、JESD22-A100-C、JESD22-A101-C。

產品特性Product characteristics

    中國電子行業儀器優質供應商——堅融實業JETYOO INDUSTRIAL & 堅友儀器JETYOO INSTRUMENTS,專業為中國區用戶提供愛斯佩克高低溫試驗箱ESPEC ARL-0680-AE系列產品儀器設備、技術培訓與售后維修服務,Support、銷售Sale、服務Service,3S公司,為上海華東地區一家以技術為導向的儀器綜合服務商,是您值得信賴的電子行業儀器專家。

 

    愛斯佩克高低溫試驗箱ESPEC ARL-0680-AE系列產品適用標準:GB/T2423.3 / IEC60068-2-78、GB/T2423.4 / IEC60068-2-30、GB/T2423.34 / IEC60068-2-38、GB/T2423.22 / IEC60068-2-14、JESD22-A100-C、JESD22-A101-C。


系列產品產品規格書
1. 型號
2. 試驗箱容量
3. 電源 電源電壓變動:額定值的±10%
4. zui大負載電流
5. 調溫調濕方式 平衡調溫調濕方式(BTHC 方式)
6. 可運行條件 環境溫度:0~+40℃
環境濕度:zui高75%rh(30℃ 75%rh 露點以下)
7. 性能 溫度箱以IEC 60068-3-5:2001、JTM K07:2007 為標準,濕度箱以IEC 60068-3-6:2001、
JTM K09:2009 為標準。根據周圍環境條件的不同,可能會有無法滿足規格性能的情況。
為環境溫度在+20℃時,額定電壓、無試樣時的性能。
7.1 溫度性能
ARL-0680-AE  ,ARL-1100-AE
溫度范圍-45~+180℃   -45~+180℃
溫度波動±0.3K   ±0.3K
溫度斜率3.0K   3.0K
試驗箱容量680L   1100L
AC380V
3φ 4W
50Hz(CE 規格*1)
AC400V
3φ 4W
50Hz(CE 規格*1)
0680 23A 22A
1100 25A 23A
*1 符合歐盟(EU)指令的CE 標識。以下稱CE 規格。

7.1.4 空間溫度偏差
3.0K 3.0K
7.1.5 溫度變化速度
除去zui高/zui低溫度間的上下10%,且在溫度變化范圍內的溫度變化速度。
上升速度(平均) -22.5℃→+157.5℃
6.3K/分 4.7K/分
下降速度(平均) +157.5℃→-22.5℃
4.8K/分 4.4K/分
下降速度(平均) 環境溫度+25℃時
4.1K/分 4.1K/分
根據環境溫度的變動,溫度變化速度(下降)按下圖所示變化。
ARL-0680
ARL-1100
溫度變化速度[K/分]
環境溫度 [℃]
溫度変化速度 [K/分]
環境溫度 [℃]
7.1.6 溫度極值達到時間
zui高/zui低溫度的到達時間
上升時間 +20℃→+180℃
0680 1100
30 分鐘以內 40 分鐘以內
下降時間 +20℃→-45℃
0680 1100
50 分鐘以內 50 分鐘以內
下降時間 +20℃→-45℃, 環境溫度+25℃時
0680 1100
62 分鐘以內 62 分鐘以內
根據環境溫度的變動,溫度極值到達時間(下降)如下圖所示變化。
7.1.7 允許發熱負荷
箱內溫度:+20℃時
0680 1100
4500W 4500W
7.2 溫濕度性能
7.2.1 溫度范圍
0680 1100
10~95℃ 10~95℃
7.2.2 濕度范圍
0680 1100
10~98%rh 10~98%rh
環境溫度 [℃]
溫度極值到達時間 [分]
注)箱內溫度40℃以下運行時,冷卻器(兼除濕器)會結霜, 連續運行將受限制。
7.2.3 濕度波動
0680 1100
±2.5%rh ±2.5%rh
7.2.4 濕度斜率
0680 1100
10%rh 10%rh
7.2.5 空間濕度偏差
0680 1100
10%rh 10%rh
7.2.6 允許發熱負荷
箱內溫濕度:+85℃ 85%rh 時
0680 1100
500W 500W
7.3 噪音
噪音的測量在無聲響的室內進行, 為試驗箱正面1m、高1.2m 處的值(JIS-Z-8731:1999 A 特
性)。受安裝環境影響,周圍的聲響等會增加噪音值,須注意安裝環境。
0680 1100
61dB 62dB
8 結構
8.1 構成材料
8.1.1 外殼 不銹鋼板(SUS430 CP、表面拉絲處理)
8.1.2 內箱 不銹鋼板(SUS304 CP、#400 表面處理)
8.1.3 隔熱材 玻璃棉+酚醛泡沫
8.2 試驗室 調溫調濕室+試驗箱
8.2.1 調溫調濕室 導風板、送風機、加熱器、冷卻器(兼 除濕器)、加濕器、空燒防止器、
加濕器供排水口、吸氣柵
8.2.2 試驗箱 干球溫度檢出端子、濕球溫度檢出端子、紗布盤、電纜孔、
試驗箱排水口、排水口用用罩子、頂部面板、
擱板支架
zui大承重 地面承重 (支架承重和地面承重的總和 試驗箱承重量 )
0680 80 ㎏
(含擱板重量)
80 ㎏
(均勻分布) 80 ㎏
1100 100 ㎏
(含擱板重量)
150 ㎏
(均勻分布) 150 ㎏
8.3 門 門把手(右把手、左鉸鏈、帶鑰匙)、一扇門、門鎖解除裝置、箱門接水盤、
溫濕度程序指示調節器(彩色LCD 顯示、通過觸摸屏設定)、
操作開關、溫度過升防止器
8.4 控制盤 主電源開關(負載開關或漏電開關)、試樣電源控制端子、
時間信號端子、通信端口、試樣溫度輸入端子
8.5 水回路室 加濕水用泵、濕球紗布供水用泵、加濕排水用泵、
機械室排熱孔(頂部)
8.6 機械室 壓縮機單元、壓縮機接露盤、冷凝器風扇、凝水盤、排水管、
機械室排熱孔(后部)、供水箱、冷凝器過濾器
8.7 電源線插入孔 頂部或背面任意選擇一個
8.8 排水管 背面一處(3 根)
8.9 供水(直連)口 背面一個
9. 尺寸和重量
9.1 尺寸
0680 1100
內尺寸 850×1000×800 1100×1000×1000
外尺寸 1050×1955×1805 1300×1955×2005
不含突出部分 (W×H×D ㎜)
9.2 重量
0680 1100
510 ㎏ 600 ㎏
10. 加熱器 鎳鉻合金電熱絲加熱器:6kW(3kW×2 個)
11 加濕器 SUS316 鎧裝加熱器(表面蒸發式)
0680 1100
4kW(2kW×2 個) 5kW(2.5kW×2 個)
12 冷卻器 板翅式冷卻器(兼除濕器) 1 個
13 冷凍方式 機械式單段壓縮冷凍方式
13.1 壓縮機 旋渦式壓縮機
13.2 冷凝器 空冷式冷凝器
13.3 膨脹機構 電子式自動膨脹閥
13.4 壓縮機容量
0680 1100
3.0kW 3.75kW
13.5 冷媒 R404A

14. 計裝
名稱 N 計裝 P-310
構成 用戶界面、主機、I/O
顯示部功能
帶觸摸屏
7.0 英寸彩色LCD
背光 LED(壽命 50,000 小時)
驅動方式 TFT
顯示像素數 800x480(WVGA)
狀態顯示LED 外部存儲指示燈、通信指示燈、定時預約指示燈、
電源指示燈
硬件開關 帶電源指示燈的電源開關(按鈕式)
控制功能 溫濕度控制功能
控制方式
PID 控制(對應試樣溫度控制)
溫度輸入
試驗箱溫度(JIS T 型熱電偶)
試樣溫度控制(JIS T 型熱電偶)
濕度輸入
試驗箱干濕球溫度輸入方式(JIS T 熱電偶)
輸入功能
100ms 高速取樣功能、斷線檢測功能
調整功能
溫度偏離設定功能
調整范圍 ±5.0℃
設定zui小分辨率 小數點后1 位
運行模式 定值運行、程序運行、遠程運行、停止
運行設定
定值設定
可設定數 3 模式
設定范圍及分辨率
溫度 -50.0℃~+185.0℃、以0.1℃為單位
濕度 0%rh~100%rh、以1%rh 為單位
設定功能
試樣溫度控制設定、濕度控制 OFF 設定、壓縮機設定、時間信號
設定、上下限報警設定、上限偏差報警設定、定值模式名稱
設定
程序設定
可設定數 40 模式(每個模式zui多99 步驟)
設定范圍及分辨率
溫度 -50.0℃~+185.0℃、以0.1℃為單位
濕度 0%rh~100%rh、以1%rh 為單位
時間 0 小時 1 分鐘 ~9999 小時59 分鐘、以1 分鐘為單位
設定功能(除定值的設定功能外還包含以下設定功能)
溫度斜率設定、濕度斜率設定、曝露時間設定、暫停設定、開始
條件設定、結束條件設定(程序間可鏈接)、計數設定(A,B)、程序
名稱設定、程序列表顯示
語言 日語、英語、中文(簡體字、繁體字)、韓語
(無需再啟動,通過畫面設定實現切換)
名稱 N 計裝 P-310
附屬功能
標準功能
基本功能
運行操作功能、報警功能、信息功能、附件功能(時間累計器、排水設定)、幫助功能、箱內監視功能(溫度濕度、外部輸出、趨勢圖)、追溯功能
管理設定功能
定時設定(開始定時、結束定時、快速定時)、取樣設定、保護設定、報警歷史顯示、版本信息、定期點檢維護一覽顯示、通知功能、帶重置功能的計時器、add on/系統更新歷史顯示
維護設定功能
通信設定(LAN設定)、設備運行動作設定(停電復位動作設定、備份運行設定、門開放時動作設定)、設定到達判定條件設定、時間信號名稱設定、畫面設定、聲音設定、日期?屏幕設定、用戶密
碼登錄、偏離調整、設備詳細設定(電源頻率、紗布連續供水設定)、試樣溫度控制環境設定
選購功能 通信功能(RS485, RS232C, GPIB)、記錄儀設定功能(輸出項目設定)、外部報警輸出設定功能、加濕延遲功能
外部存儲功能
接口
USB2.0 標準
(插口A 型)
500mA(zui大)
對應設備 USB 大容量閃存卡
對應文件格式 FAT16/FAT32
對應功能
?取樣寫入設定
?程序模式寫入/讀取
?追溯數據寫入
?add on/系統更新
對應PC應用 模式manager Lite
※模式manager Lite 可在Test Navi 產品會員下載。
網絡功能
接口
Ethernet 接口
(100baseTX)
通信協議 TCP/IP(HTTP, SMTP,IPv4)
Web 應用
監視功能、設定功能、 運行操作功能、
數據收錄功能、管理設定?維護設定功能、
電子郵件通知功能
對應瀏覽器
Windows Internet Explorer10
PC 通信功能 Ethernet 接口 和PC 1 対1 連接
動作環境
性能保證環境 溫度+23℃±5℃、濕度30%rh~90%rh(無結露)
動作保證環境 溫度0℃~+60℃、濕度30%rh~90%rh(無結露)
保存環境 溫度-20℃~+70℃、濕度20%rh~95%rh(無結露)
顯示精度
溫度(T 型熱電偶)
(環境溫度 +23℃±1℃時)
測量精度 ±0.3℃
顯示精度(滿量程) ±(0.07%FS+1digit)
時間 月差 60 秒以內 +23.0℃±5℃
9 愛斯佩克株式會社
15. 主電源開關
負載開關(AC380V/AC400V)
主電源開/關用
(1)額定電壓 AC380V/AC400V 3φ N/PE 50Hz
主電源未配備斷路器。
須設置斷路器(32A SLOW)。
(2)額定電流 32A
16. 箱內循環用送風機 多葉片風扇
16.1 驅動方式 電動機直結方式
16.2 電動機 100W 2 個
17. 冷凝器用送風機 低噪音型有壓換氣扇
100W 2 個
18. 裝備品
18.1 電纜孔 右側面 φ100 ㎜ 1 個
左側面 φ100 ㎜ 1 個
18.2 腳輪 自由腳輪 4 個
18.3 調整腳 4 個
18.4 時間信號端子
試驗狀態報* 接點容量 AC250V 1A 2 點
18.5 試樣電源控制端子
試驗保護用 接點容量 AC250V 3A 1 個
18.6 試樣溫度輸入端子 1 個
18.7 電源線 不附帶。
19. 附件
19.1 電纜孔橡膠栓 φ100 ㎜ 硅膠海綿橡膠 2 個
19.2 支架
19.2.1 擱條 不銹鋼板(SUS304 CP) 1 組
19.2.2 擱板 不銹鋼線(SUS304) 1 張
外尺寸 擱板重量 擱板承重
(均勻分布)
0680 817×27×750 6 ㎏ 40 ㎏
1100 1067×28×950 12 ㎏ 50 ㎏
(W×H×D ㎜)
編號 4412001007021
19.3 玻璃管保險絲 B 型 250V 0.4A、5A、8A 各1 根
19.4 濕球紗布 紗布 24 張、吸管 1 根 1 盒
19.5 試樣溫度測定用熱電偶
T 型熱電偶(3m)(IEC 60584-1:1995) 1 根
19.6 試樣溫度輸入接口 1 個
19.7 用戶操作手冊 CD、設置要領書 1 套
19.8 鑰匙 門用 2 個
20. 安全功能
功能 目的 動作內容
1 控制回路1 過電流保護 保護設備 a
2 系統異常 保護設備 b
3 逆轉防止繼電器 保護設備 b
4 溫度保險絲 保護設備 b
5 送風機溫度開關 保護設備 b
6 送風機短路保護玻璃管保險絲 保護設備 b
7 溫度過升防止器 保護試樣 b
8 室溫補償斷線ト檢出回路 保護設備 b
9 干球溫度斷線檢出回路 保護設備 B
10 試樣溫度斷線檢出回路(僅在試樣溫度控制中) 保護設備 B
11 冷凝器風扇短路保護 保護設備 B
12 冷凝器風扇過負載保護 保護設備 B
13 壓縮機1 溫度傳感器斷線檢出回路 保護設備 b
14 壓縮機1 短路保護 保護設備 b
15 壓縮機1 過電流保護 保護設備 b
16 壓縮機1 吐出管溫度開關 保護設備 b
17 壓縮機1 高低壓壓力開關 保護設備 b
18 壓縮機1 結霜檢出回路 保護設備 b
19 壓縮機1 回路溫度范圍外 保護設備 b
20 加熱器?加濕器過電流保護 保護設備 b
21 控制回路2 過電流保護 保護設備 b
22 控制回路短路保護玻璃管保險絲 保護設備 b
23 溫度上下限報警功能 (內置于溫濕度調節器) 保護試樣 b
24 濕球溫度斷線檢出回路 保護設備 c
25 加濕器空燒防止器 保護設備 c
26 加濕器水位檢測 保護設備 c
27 溫度上限偏差報警功能(內置于溫濕度調節器) 保護試樣 d
28 濕度上下限報警功能 (內置于溫濕度調節器) 保護試樣 d
29 供水箱缺水開關 保護設備 e
30 門開關 保護人員 f
功能 目的 動作內容
31 紗布干燥檢出 保護設備 g
32 供水箱低水位開關 保護設備 g
33 試樣電源控制端子 保護試樣 h
a : 整個設備停止。
b : 顯示警報,報警蜂鳴器發出聲響。設備停止運行。
c : 顯示警報,報警蜂鳴器發出聲響。 。
備份運行OFF 時,設備停止運行。
備份運行ON 時,設備繼續溫度運行。
d : 顯示警報, 報警蜂鳴器發出聲響。設備進行所定的安全動作。
e : 顯示警報,報警蜂鳴器發出聲響。設備繼續溫度運行。
f : 顯示警報,報警蜂鳴器發出聲響。
暫停動作OFF 時,設備繼續運行。
暫停動作ON 時,設備暫停運行。
報警顯示、報警蜂鳴器可選擇ON/OFF。
g : 顯示警報,報警蜂鳴器發出聲響。設備繼續運行。
h : 設備運行停止或運行停止的安全裝置動作時,停止對試樣的供電。
21. 供水
21.1 供水方式 供水泵供水
21.2 水箱安裝位置
機械室正面
21.3 水箱容量 40L(固定式水箱 20L×2 個)
21.4 自動供水口 口徑:Rc3/8(后部)
21.5 水質 導電率:0.1~10μS/㎝
6~7pH 的純水
21.6 供水壓力 0.01MPa~0.05MPa
22. 試樣的限制 以下物質不得用于試驗。
? 爆炸性物質,可燃性物質及含有該類物質的物質
? 具有腐蝕性的物質
? 生物
? 超過容許發熱負荷的物質
23. 除外項目
? 搬入?安裝場地的準備工程
? 一次電源工程
? 供排水工程

    

系列產品技術規格參數指標

愛斯佩克ESPEC高低溫濕熱試驗箱ARL-0680-AE,ARL-1100-AE   Model ARL−0680 ARL−1100  Model ARS−0220 ARS−0390 ARS−0680 ARS−1100   Model ARU−0680 ARU−1100   Model ARG−0220 ARG−0390 ARG−0680 ARG−1100   (ARS-0680/1100, ARG-0680/1100)
AR series has big allowable heat loads generated by the specimen,
and achieves improved temperature change rate in an expanded temperature and humidity range.
The new N-instrumentation allows AR series chambers to support easy-to-use networking system.
ESPEC offers two temperature control ranges: −75℃ to +180℃ or −45℃ to +180℃ ,
with or without humidity control (10 to 98%rh).
These models incorporate the most desirable features in temperature and humidity chambers.
ARS−0220
*Viewing window is optional.
ARS−1100
Advanced reliability
Environmental Stress Chambers
1
2
Superior temperature heating
and cooling control
at 3℃ /min. with specimen load
Temperat ure heating and cooling
performance at 4 to 6℃ /min. (no load),
and can handle temperature cycle tests at
3℃ /min. (with load*)
* ARS-1100 specimen: aluminum 38kg
(including shelf 12kg)
Highly uniform temperature
distribution
Highly uniform temperature distribution
minimizes variations in test results.
Reduced temperature and
humidity stabilization time
Temperature and humidity stabilization
time is greatly reduced by minimizing
hunting as the chamber approaches setpoint. (under testing operation from RT
to 85℃ /85% rh).
Wider control range for
temperature and humidity
Features a wider control range of
temperature and humidity, including
stable control at 95℃ /98% rh.
Meets international standards
D e sig ne d t o c omply w it h m ajor
environmental test standards such as
IEC60068-2, or ISO16750-4 (5.3).
(Refer to compatible test standards)
International safety standard
compliance
Complies with Safety of Machinery
(ISO 12100), Low Voltage (IEC 60204),
EMC (IEC 61000-6-2, IEC 61000-6-4).
Temperature (℃)
100
90
98
80
70
60
50
40
30
20
10
10 20 30 40 50 60 70 80
95
90 100
0
Relative
Humidity
(%rh)
ARS?ARL
PR?PL?PSL
*Continuous operation at or below +40℃ is limited because of frost formation on the cooler
and dehumidifier.
Temperature & Humidity Control Range
(ambient temperature at +20℃ with no load)
Characteristics
● Compatible Test Standards
?IEC60068-2-1: Cold
?IEC60068-2-2: Dry heat
?IEC60068-2-3: Damp heat, steady state
?IEC60068-2-14 Nb: Change of temperature with
specified rate of change *
?IEC60068-2-38: Composite temperature/ humidity
cyclic test *
?IEC60068-2-78: Damp heat, steady state
?ISO16750-4 5.3: Temperature cycling
Model Heat up (K/min.) Pull down (K/min.)
ARL/ARU−0680 6.3 4.8
ARL/ARU−1100 4.7 4.4
ARS/ARG−0220 6.0 5.2
ARS/ARG−0390 5.0 4.0
ARS/ARG−0680 6.0 4.2
ARS/ARG−1100 4.7 4.1
Temperature change rate
*At ambient temperature, +20℃ no specimen.
Safety precautions
● Do not use specimens which are explosive or flammable, or which
contain such substances.

Supports heat loads
up to 4500W*
(During temperature testing)
Supports electrically-charged specimens,
and can compensate up to 4500W of
heat load during temperature testing,
depending on the chamber model (500W
during temperature and humidity
testing).
* Test area temperature:+20℃
User-friendly features
Standard features include cable ports on
both sides which allow free access of
the test area. Antirust and oil proof 18-8
Cr-Ni stainless steel plate is used as
external panels. It is possible to select
water supply via water tank or direct
water coupling alliteratively all the
time.
Chamber restricted to
lock the door
It is now possible to lock the chamber
door to prevent accidental operation of
the chamber during testing.
The handle part design has also been
improved so the door closing is easier
and safer.
New refrigeration circuit and
     condenser filter improves
reliability
Thanks to newly designed refrigeration
circuit, reliability is improved. And
further more condenser filter, prevents a
condenser fan from clogging becomes
standard equipment.
Cable ports on both walls
Water tank Key
Characteristics
4
Controller N-instrumentation
N-instrumentation equipped
with a color LCD touch panel
Wide 7-inch screen with LED backlight
is clearer and provides faster display
speed.
Interior light button
It is able to switch ON/OFF from the
interior light button any time.
Information button
When there are some things need to be
notified to the operator, information
button will alart to the operator. By
pressing the button, you will find
notifications such as "Check Humidity
Tray".
Trend graph output on
USB memory
Trend graphs can be displayed on the
web application or downloaded on USB
m e m o r y. I t i s a l s o p o s s i b l e t o
continuously register data on USB
memory if numerous data records are
needed.
N-instrumentation
USB memory port
Touch icon to show
navigation bar.
Touch navigation
Interior light
Display TFT Color LCD (7.0inch)
Operating mode Constant operation, Program operation, Remote operation, Stop
Setting range
● Constant setup: 3 patterns
Setting range: Temp.: −80.0℃ to +185.0℃ , 0.1℃ unit (ARS, ARG)
Temp.: −50.0℃ to +185.0℃ , 0.1℃ unit (ARL, ARU)
Humidity: 0 to 100% rh, 1% unit (ARS, ARL)
● Program setup: 40 patterns (99 steps)
Setting range: Temp.: −80.0℃ to +185.0℃ , 0.1℃ unit (ARS, ARG)
−50.0℃ to +185.0℃ , 0.1℃ unit (ARL, ARU)
Humidity: 0 to 100% rh, 1% unit
Time: 0 hour and 1 min. to
9999 hours and 59 min. 1 min. unit
Language Japanese, English, Chinese (simplified, traditional), Korean
Interface USB 2.0 standard compliant (A-type connector)
External memory
function
Write sampling data, Read/ Write program, Backtrace output,
Add-on/system updates
Network function Interface: Ethernet port (100base-TX)
Web function Monitoring, setting, operation, Data Record Function,
maintenance setting, alert
Browser Windows Internet Explorer10
Application of USB MEMORY
Continous record test data
Data transfer
Copy test program
5
Network
Remote monitoring and control
(Ethernet connection)
A unique web application allows the
user to monitor the chamber, set
programs, and start and stop operation
from a PC connected to the chamber
Ethernet port (LAN’s port). No software
required, the chamber can be accessed
and controlled from PC via a web
browser (Smartphone, tablets and the
like can also be used).
Wireless connection and multiple units
connection are also possible.
alert
When an alarm is triggered, an is
sent to the registered PC or
address. A notification can also be sent
at the time of test completion.
*Requires an intranet environment capable of
sending s.
Multilingual display
The language available for the Web
application (Japanese/ English/ Simplified
Chinese/ Traditional Chinese/ Korean)
can be changed without affecting the
N-instrumentation language display.
Remote monitoring and control thanks to a Web application
Ethernet
無線LANによる接続例
內蔵ワイヤレスダイレクトによる接続例
Program copy and computer editing
攜帯
スマートフォン
タブレットコントローラー
(オプション)
PC
Edit
Copy
小型環境試験器
(Wi-Fi機能搭載)
Wi-Fiルーター
(オプション)
スマートフォン
スマートフォン
小型環境試験器
小型環境試験器
ワイヤレスダイレクト
(オプション)
Program copy and computer editing
Edit
Copy
AR series
Ethernet
Network
Wi-Fi router
Smartphone Tablet controller
PC
Ethernet
phone
Smartphone
Mail server
Intranet
(company LAN)
alert
PC
AR series
Environmental
Stress Chamber
● Program editing ● Graph display
Image
Screen
Privileges Chamber monitor Constant Mode/ Program Setup Run/ Stop configuration Device
Administrator ○ ○ ○ ○
Operator ○ ○ ○ ×
User ○ × × ×
Login information
○= available; ×= Not available
6
Network
エスペック ネットワーク 検 索
エスペック オンライン 検 索
試験棟
集中管理システム (舊:Web統合管理システム)(別売)
100臺までの試験器の狀態を1畫面で確認することができる
集中管理システムに接続可能です。
Ethernet
ハイパワー恒溫(恒濕)器
ネットワークアダプター
舊:RS-485
LANコンバーター
Ethernet
プラチナスKシリーズ
事務棟
Ethernet
Ethernet
集中管理システム
クライアントPC
イントラネット
2015年3月対応予定
Lab
Web Integrated Network (Sold separay)
Maximum 100units of connected chambers and other peripherals necessary
for environmental testing are manned via Internet.
Ethernet
AR series
LAN converter
Ethernet
Platinous K Series
Office
Ethernet
Ethernet
Web integrated
network system
Client PC
Intranet
Access to video
Copy and reproduce testing
Thanks to the USB memory you can
copy the same test program in multiple
chambers, provided that they have the
same operation range. No need to
program each chamber, just connect the
USB and the test can start.
Download edit programs online
Via the Pattern Manager Lite software
installed on your PC, edit programs
according to your testing needs, and
upload them with a USB.
Edit programs
Through our online website Test Navi,
dedicated to reliability and testing
information, you can find most of the
recognized international standard,
available for download.
Charge them as is on your USB memory,
or edit them and transfer to your chamber.
* Test Navi is a website dedicated to reliability
testing information and technologies. http://
www.test-navi。。com/eng/index.html
The Pattern Manager Lite software allows
you to edit programs for your chamber,
view and edit data as graph, etc.
The software can be downloaded from the
Test Navi website.
製品會員専用サイト
パターンマネージャーの情報、
WEBマネージャー情報のダウンロード
環境試験規格一覧
パターンマネージャーLite対応
試験條件プログラムパターンダウンロード
ダウンロード
試験規格プログラムパターン
ファイルの活用方法
活用方法をムービーでご覧いただけます。 ムービー
Product registration
membership Website
Download Pattern Manager and
WEB Manager information.
Environmental Test
Standards
For Pattern Manager Lite
Test methods download
Download
Product Registration
Membership Website
製品會員専用サイト
パターンマネージャーの情報、
WEBマネージャー情報のダウンロード
環境試験規格一覧
パターンマネージャーLite対応
試験條件プログラムパターンダウンロード
ダウンロード
試験規格プログラムパターン
ファイルの活用方法
活用方法をムービーでご覧いただけます。 ムービー
Product registration
membership Website
Download Pattern Manager and
WEB Manager information.
Environmental Test
Standards
For Pattern Manager Lite
Test methods download
Download
Product Registration
Membership Website
● Test Navi
(http://www.test-navi。。com/eng/index.html)
This website provides practical knowledge on environmental testing
that ESPEC has acquired through years of experience, as well as
covering everything from the fundamentals to the latest information on
environmental and reliability testing.
? Updates for chamber controller software
? Search for environmental test standards
? Download test profiles from a list of environmental test standards
Ethernet
無線LANによる接続例
內蔵ワイヤレスダイレクトによる接続例
Program copy and computer editing
攜帯
スマートフォン
タブレットコントローラー
(オプション)
PC
Edit
Copy
小型環境試験器
(Wi-Fi機能搭載)
Wi-Fiルーター
(オプション)
スマートフォン
スマートフォン
小型環境試験器
小型環境試験器
ワイヤレスダイレクト
(オプション)
Program copy and computer editing
Edit
Copy
AR series
Ethernet
Network
Wi-Fi router
Smartphone Tablet controller
PC
Ethernet
phone
Smartphone
Mail server
Intranet
(company LAN)
alert
PC
AR series
Environmental
Stress Chamber
7
TEMPERATURE & HUMIDITY CHAMBER
ARL −45 to +180℃?10 to 98%rh


愛斯佩克ESPEC高低溫濕熱試驗箱Model ARL−0680 ARL−1100 
System Balanced Temperature & Humidity Control (BTHC) system
Temp. performance *1
Temp. range −45 to +180℃ (−49 to +356℉ )
Temp. fluctuation ±0.3K
Temp. variation in space 3.0K
Temp. rate
of change *2
Heat up rate 6.3 K/min. 4.7 K/min.
Pull down rate 4.8 K/min. 4.4 K/min.
Max. allowable heat load 4500 W Test area temperature: +20℃
Temp. & humid.
performance *1
Temp. & humid. range +10 to +95℃ / 10 to 98%rh
Humid. fluctuation ±2.5%rh
Max. allowable heat load 500 W Test area conditions: +85℃ /85%rh
Construction
Exterior material 18 Cr-stainless steel plate (Hairline finish)
Test area material 18-8 Cr-Ni Stainless steel plate (BA finish)
Insulation Foamed phenol, glass wool
Heater Nichrome strip wire heater (3 kW×2)
Humidifier Sheathed heater
Cooler Plate fin cooler and dehumidifier
Refrigeration unit
System Mechanical single-stage refrigeration system
Refrigerator Scroll-type compressor
Refrigerator capacity 3.0 kw 3.75 kw
Expansion mechanism Electronic expansion valve
Refrigerant R404A
Air circulator Sirocco fan
Interface Ethernet
Fittings 100mm cable port (×2), specimen power supply control terminal, condenser filter,
specimen temperature input terminal, time signal (×2), casters with levelling feet (×4)
Capacity 680 L 1100 L
Chamber total load resistance 80 kg 150 kg
Inside dimensions mm (inch) *3 W850×H1000×D800 (W33.5×H39.4×D31.5) W1100×H1000×D1000 (W43.3×H39.4×D39.4)
Outside dimensions mm (inch) *3 W1050×H1955×D1805 (W41.3×H77.0×D71.1) W1300×H1955×D2005 (W51.2×H77.0×D78.9)
Weight 510 kg 600 kg
Utility requirements
Allowable ambient conditions 0 to +40℃ (+32 to +104℉ ) / 75%rh max.
Power
supply *4
200V AC 3φ50/60Hz 53 A 56 A
220V AC 3φ60Hz 49 A 52 A
380V AC 3φ50Hz 23 A 25 A
400V AC 3φ50Hz *5 22 A 23 A
Noise level *6 61 dB 62 dB
Exhaust heat quantity kJ/h (kcal/h) 32400 (7743) 39600 (9464)
*1: At ambient temperature +20℃ , no specimen. Performance shown above conforms to IEC 60068-3-5:2001 and IEC 60068-3-6:2001.
*2: Temperature rate of change in the temperature range excluding ±10% of max/min. temperature.
*3: Excluding protrusions.
*4: Power supply voltage fluctuation to be ±10% of rated value.
*5: Conforms to CE marking based on EU directives.
*6: Measurements are to be taken in an anechoic room at a height of 1.2m from the floor and a distance of 1m from the chamber front panel
(ISO 1996-1:2003 _ A-weighted sound pressure level).
8
TEMPERATURE & HUMIDITY CHAMBER
ARS −75 to +180℃?10 to 98%rh


愛斯佩克ESPEC高低溫濕熱試驗箱Model ARS−0220 ARS−0390 ARS−0680 ARS−1100 
System Balanced Temperature & Humidity Control (BTHC) system
Temp. performance *1
Temp. range −75 to +180℃ (−103 to +356℉ )
Temp. fluctuation ±0.3K
Temp. variation in space 3.0K
Temp. rate
of change *2
Heat up rate 6.0 K/min. 5.0 K/min. 6.0 K/min. 4.7K/min.
Pull down rate 5.2 K/min. 4.0 K/min. 4.2 K/min. 4.1K/min.
Max. allowable heat load Test area temperature: +20℃
3000 W 4500 W
Temp. & humid.
performance *1
Temp. & humid. range +10 to +95℃ / 10 to 98%rh
Humid. fluctuation ±2.5%rh
Max. allowable heat load Test area conditions: +25 to +95℃ /90%rh Test area conditions: +85℃ /85%rh
350 W 300 W 500 W
Construction
Exterior material 18 Cr-stainless steel plate (Hairline finish)
Test area material 18-8 Cr-Ni Stainless steel plate (BA finish)
Insulation Foamed phenol, glass wool
Heater Nichrome strip wire heater
(1.75 kW×2) (3 kW×2)
Humidifier Sheathed heater
Cooler Plate fin cooler and dehumidifier
Refrigeration unit
System Mechanical cascade and compression refrigeration system
Refrigerator Rotary compressor Scroll compressor
Refrigerator capacity Unit 1: 2.2 kw ×1,
Unit 2: 2.2 kw ×1
Unit 1: 3.0 kw ×1,
Unit 2: 3.0 kw ×1
Unit 1: 3.75 kw ×1,
Unit 2: 3.75 kw ×1
Expansion mechanism Electronic expansion valve
Refrigerant R404A, R508A R404A, R23
Air circulator Sirocco fan
Interface Ethernet
Fittings 100mm cable port (×2), specimen power supply control terminal, condenser filter,
specimen temperature input terminal, time signal (×2), casters with levelling feet (×4)
Capacity 220 L 390 L 680 L 1100 L
Chamber total load resistance 50 kg 80 kg 80 kg 150 kg
Inside dimensions mm (inch) *3 W700×H800×D400
(W27.6×H31.5×D15.8)
W700×H800×D700
(W27.6×H31.5×D27.6)
W850×H1000×D800
(W33.5×H39.4×D31.5)
W1100×H1000×D1000
(W43.3×H39.4×D39.4)
Outside dimensions mm (inch) *3 W900×H1742×D1455
(W35.4×H68.6×D57.3)
W900×H1742×D1705
(W35.4×H68.6×D67.1)
W1050×H1955×D1805
(W41.3×H77.0×D71.1)
W1300×H1955×D2005
(W51.2×H77.0×D78.9)
Weight 390 kg 405 kg 615 kg 700 kg
Utility requirements
Allowable ambient conditions 0 to +40℃ (+32 to +104℉ ) / 75%rh max.
Power
supply *4
200V AC 3φ50/60Hz ─ ─ 63 A 70 A
220V AC 3φ60Hz 38 A *5 38 A *5 58 A 64 A
380V AC 3φ50Hz 24 A *5 24 A *5 28 A 32 A
400V AC 3φ50Hz *5 23 A 23 A 27 A 29 A
Noise level *6 57 dB 58 dB 62 dB 63 dB
Exhaust heat quantity kJ/h (kcal/h) 26600 (6357) 26600 (6357) 39600 (9464) 46800 (11185)
*1: At ambient temperature +20℃ , no specimen. Performance shown above conforms to IEC 60068-3-5:2001 and IEC 60068-3-6:2001.
*2: Temperature rate of change in the temperature range excluding ±10% of max/min. temperature.
*3: Excluding protrusions.
*4: Power supply voltage fluctuation to be ±10% of rated value.
*5: Conforms to CE marking based on EU directives.
*6: Measurements are to be taken in an anechoic room at a height of 1.2m from the floor and a distance of 1m from the chamber front panel
(ISO 1996-1:2003 _ A-weighted sound pressure level).
9


愛斯佩克ESPEC高低溫濕熱試驗箱Model ARU−0680 ARU−1100  
System Balanced Temperature Control (BTC) system
Temp. performance *1
Temp. range −45 to +180℃ (−49 to +356℉ )
Temp. fluctuation ±0.3 K
Temp. variation in space 3.0 K
Temp. rate
of change *2
Heat up rate 6.3 K/min. 4.7 K/min.
Pull down rate 4.8 K/min. 4.4 K/min.
Max. allowable heat load 4500 W Test area temperature: +20℃
Construction
Exterior material 18 Cr-stainless steel plate (Hairline finish)
Test area material 18-8 Cr-Ni Stainless steel plate (BA finish)
Insulation Foamed phenol, glass wool
Heater Nichrome strip wire heater (3kW ×2)
Cooler Plate fin cooler
Refrigeration unit
System Mechanical single-stage refrigeration system
Refrigerator Scroll-type compressor
Refrigerator capacity 3.0 kw 3.75 kw
Expansion mechanism Electronic expansion valve
Refrigerant R404A
Air circulator Sirocco fan
Interface Ethernet
Fittings 100mm cable port (×2), specimen power supply control terminal, condenser filter,
specimen temperature input terminal, time signal (×2), casters with levelling feet (×4)
Capacity 680 L 1100 L
Chamber total load resistance 80 kg 150 kg
Inside dimensions mm (inch) *3 W850×H1000×D800 (W33.5×H39.4×D31.5) W1100×H1000×D1000 (W43.3×H39.4×D39.4)
Outside dimensions mm (inch) *3 W1050×H1955×D1805 (W41.3×H77.0×D71.1) W1300×H1955×D2005 (W51.2×H77.0×D78.9)
Weight 505 kg 595 kg
Utility requirements
Allowable ambient conditions 0 to +40℃ (+32 to +104℉ ) / 75%rh max.
Power
supply *4
200V AC 3φ50/60Hz 53 A 56 A
220V AC 3φ60Hz 49 A 52 A
380V AC 3φ50Hz 23 A 25 A
400V AC 3φ50Hz *5 22 A 23 A
Noise level *6 61 dB 62 dB
Exhaust heat quantity kJ/h (kcal/h) 32400 (7743) 39600 (9464)
TEMPERATURE CHAMBER
ARU −45 to +180℃
*1: At ambient temperature +20℃ , no specimen. Performance shown above conforms to IEC 60068-3-5:2001.
*2: Temperature rate of change in the temperature range excluding ±10% of max/min. temperature.
*3: Excluding protrusions.
*4: Power supply voltage fluctuation to be ±10% of rated value.
*5: Conforms to CE marking based on EU directives.
*6: Measurements are to be taken in an anechoic room at a height of 1.2m from the floor and a distance of 1m from the chamber front panel
(ISO 1996-1:2003 _ A-weighted sound pressure level).
10


愛斯佩克ESPEC高低溫濕熱試驗箱Model ARG−0220 ARG−0390 ARG−0680 ARG−1100  
System Balanced Temperature Control (BTC) system
Temp. performance *1
Temp. range −75 to +180℃ (−103 to +356℉ )
Temp. fluctuation ±0.3 K
Temp. variation in space 3.0 K
Temp. rate
of change *2
Heat up rate 6.0 K/min. 5.0 K/min. 6.0 K/min. 4.7K/min.
Pull down rate 5.2 K/min. 4.0 K/min. 4.2 K/min. 4.1K/min.
Max. allowable heat load
Test area temperature: +20℃
3000 W 4500 W
Construction
Exterior material 18 Cr-stainless steel plate (Hairline finish)
Test area material 18-8 Cr-Ni Stainless steel plate (BA finish)
Insulation Foamed phenol, glass wool
Heater
Nichrome strip wire heater
(1.75 kW×2) (3 kW×2)
Cooler Plate fin cooler
Refrigeration unit
System Mechanical cascade refrigeration system
Refrigerator Scroll-type compressor
Refrigerator capacity Unit 1: 2.2 kw ×1,
Unit 2: 2.2 kw ×1
Unit 1: 3.0 kw ×1,
Unit 2: 3.0 kw ×1
Unit 1: 3.75 kw ×1,
Unit 2: 3.75 kw ×1
Expansion mechanism Electronic expansion valve
Refrigerant R404A, R508A R404A, R23
Air circulator Sirocco fan
Interface Ethernet
Fittings 100mm cable port (×2), specimen power supply control terminal, condenser filter,
specimen temperature input terminal, time signal (×2), casters with levelling feet (×4)
Capacity 220 L 390 L 680 L 1100 L
Chamber total load resistance 50 kg 80 kg 80 kg 150 kg
Inside dimensions mm (inch) *3 W700×H800×D400
(W27.6×H31.5×D15.8)
W700×H800×D700
(W27.6×H31.5×D27.6)
W850×H1000×D800
(W33.5×H39.4×D31.5)
W1100×H1000×D1000
(W43.3×H39.4×D39.4)
Outside dimensions mm (inch) *3 W900×H1742×D1455
(W35.4×H68.6×D57.3)
W900×H1742×D1705
(W35.4×H68.6×D67.1)
W1050×H1955×D1805
(W41.3×H77.0×D71.1)
W1300×H1955×D2005
(W51.2×H77.0×D78.9)
Weight 385 kg 400 kg 615 kg 700 kg
Utility requirements
Allowable ambient conditions 0 to +40℃ (+32 to +104℉ ) / 75%rh max.
Power
supply *4
200V AC 3φ50/60Hz ─ ─ 63 A 70 A
220V AC 3φ60Hz 38 A *5 38 A *5 58 A 64 A
380V AC 3φ50Hz 24 A *5 24 A *5 28 A 32 A
400V AC 3φ50Hz *5 23 A 23 A 27 A 29 A
Noise level *6 57 dB 58 dB 62 dB 63 dB
Exhaust heat quantity kJ/h (kcal/h) 26600 (6357) 26600 (6357) 39600 (9464) 46800 (11185)
TEMPERATURE CHAMBER
ARG −75 to +180℃
*1: At ambient temperature +20℃ , no specimen. Performance shown above conforms to IEC 60068-3-5:2001.
*2: Temperature rate of change in the temperature range excluding ±10% of max/min. temperature.
*3: Excluding protrusions.
*4: Power supply voltage fluctuation to be ±10% of rated value.
*5: Conforms to CE marking based on EU directives.
*6: Measurements are to be taken in an anechoic room at a height of 1.2m from the floor and a distance of 1m from the chamber front panel
(ISO 1996-1:2003 _ A-weighted sound pressure level).
11
Model 0220 0390 0680 1100
Shelf size (mm) W667
D350
W667
D650
W817
D750
W1067
D950
Shelf weight 2 kg 3 kg 6 kg 12 kg
Shelf load capacity
(evenly distributed load) 30 kg 30 kg 40 kg 50 kg
Shelf support max. load
(Including shelf weight) 50 kg 80 kg 80 kg 100 kg
● Control circuit overcurrent protection
● Control circuit short circuit protection cartridge fuse
● System error
● Reverse-prevention relay
● Thermal fuse
● Temperature switch for air circulator
● Air circulator short circuit protection
● Ambient temperature input burn-out detection circuit
● Dry-bulb temperature input burn-out detection circuit
● Specimen temperature input burn-out detection circuit
(only when using specimen temperature control)
● Condenser fan short circuit protection
● Condenser fan overload protection
● Refrigerator temperature sensor burned detect circuit
● Refrigerator short circuit protection
● Refrigerator overcurrent protection
● Refrigerator discharge pipe temperature switch (0680/1100)
● Refrigerator high (low) pressure switch
● Refrigerator frost detection cicuit (0680/1100)
● Refrigerator circuit temperature range over
● Refrigerator frost trouble detection temperature switch
(ARS-0680/1100, ARG-0680/1100)
● Refrigerator discharge pipe temperature trouble detection circuit
(ARS, ARG)
● Heater (humidifier) leak current protection
● Wet bulb temperature input burnout detection circuit
(ARL, ARS)
● Humidifier boil-dry protector (ARL, ARS)
● Humidifier water level detector (ARL, ARS)
● Water tank empty switch (ARL, ARS)
● Water tank low level switch (ARL, ARS)
● Dry wick detection (ARL, ARS)
● Overheat protector
● High deviation temperature alarm
(built into temperature and humidity controller)
● High/ low absolute temperature (humidity) alarms
(built into temperature and humidity controller)
● Specimen power supply control terminal
● Chamber door switch
ACCESSORIES SAFETY DEVICES
SHELVES SIZE AND LOAD RESISTANCE
● Cable port rubber plug (φ100 mm) 2 each
● Shelf brackets 1 set
stainless steel plate (18-8 Cr-Ni stainless steel)
● Shelf 1
stainless steel wire (18-8 Cr-Ni stainless steel)
● Door key 2
● Cartridge fuse (Class B, 250 V 0.4 A, 5 A, 8 A)     1 each
● Wet-bulb wick (ARL, ARS) 1 box (24 wicks)
● Specimen temperature measuring thermocouple (type T, 3m) 1
● Specimen temperature input connector 1
● Operation manual 1
12
OPTIONS
UTILITY TEST SAMPLE SETTING OBSERVATION
Additional cable port
Provided in addition / replacement of
the standard cable ports.
?50 mm diameter
?100 mm diameter
* Each cable port is equipped with a silicone
sponge rubber plug.
Cable port rubber plug
Prevents air leakage from the cable
port.
Portable tank
Power cable
Used to refill the standard tank.
*ARS, ARL only
?2.5 m
?5 m
?10m
*The chamber does not come with a power cable.
Water purifier (WS-1)
Water purifier with reverse osmosis
membrane. Produces approx 6.6L per
hour (at primary water temp. +10℃ ).
Shelf, shelf bracket
Equivalent to standard accessory.
Heavy-duty shelf
Us e d t o hold he av y s p e c i me n s
exceeding the load capacity of the
standard shelf.
Load capacity: 50kg (max. 2 shelves)
*Standard for 1100L model
Viewing window
Used for observation of the specimens
inside the chamber.
Dimensions: W340×H440 mm
NETWORK
Communication cables
?RS-485 5m/ 10m/ 30m
?RS-232C 1.5m/ 3m/ 6m
?GPIB 2m/ 4m
Interface
Computer interface
?RS-485
?GPIB
?RS-232C
Water leak detection system and
dew tray to catch dripping water
are also available to detect and
prevent water damages.
OPTIONS
13
Temperature recorder (digital)
Portable type
−100 to +200℃ 6 dots
Temperature and humidity recorder (digital)
Portable type
−100 to +200℃ / 0 to 100%rh 6 dots
Temperature sensor terminal
Terminal board for dry-bulb temperature sensor in the chamber.
DC output terminal
Outputs temperature, humidity, and
temperature of the specimen from the
test area.
Relay contact output
Up to 8 contacts can be added to the
standard 2 relay contacts (time signals).
Paperless recorder - portable type
Records temperature of each section
such as the temperature inside the
chamber.
Data saving cycle: 5 sec.
External recording media:
CF memory card (256MB)
USB port
Language support: ENG, JPN
[Temperature type]
Temperature range: −100 to +200℃
Number of inputs: Temperature 1
(5 more channels can be turned ON)
[Temperature and humidity type]
Temperature range: −100 to +200℃
Humidity range: 0 to 100%rh
Number of inputs:
Temperature 1 / Humidity 1
(4 more channels can be turned ON)
OPTION
OPTION
OPTION
OPTION
MODE
MODE
SPECIMEN
TEMPERATURE INPUT
(TYPE T)
試料溫度入力
(JIS T)
POWER SUPPLY
CONTROL
FOR SPECIMEN

No.2
試料電源制御出力
タイムシグナル出力
TIME SIGNALS
ETHERNET
No.6
No.7
No.8
0
No.9
タイムシグナル出力
TIME SIGNALS
外部警報出力
EXTERNAL ALARM
SIGNAL
No.3
No.5
No.4
EXTRA OVERHEAT
PROTECTOR
追加溫度過昇防止器
OVERCOOL PROTECTOR
溫度過冷防止器
槽內溫度
(JIS T)
モニタ出力 (DC1-5V リニア)
CHAMBER TEMPERATURE
(TYPE T)
MONITOR OUTPUT
(1-5V DC LINEAR)
記録計用出力
RECORDER OUTPUT
OFF
OPTION
OPTION
OPTION
OPTION
MODE
MODE
SPECIMEN
TEMPERATURE INPUT
(TYPE T)
試料溫度入力
(JIS T)
POWER SUPPLY
CONTROL
FOR SPECIMEN

No.2
試料電源制御出力
タイムシグナル出力
TIME SIGNALS
ETHERNET
No.6
No.7
No.8
0
No.9
タイムシグナル出力
TIME SIGNALS
外部警報出力
EXTERNAL ALARM
SIGNAL
No.3
No.5
No.4
EXTRA OVERHEAT
PROTECTOR
追加溫度過昇防止器
OVERCOOL PROTECTOR
溫度過冷防止器
槽內溫度
(JIS T)
モニタ出力 (DC1-5V リニア)
CHAMBER TEMPERATURE
(TYPE T)
MONITOR OUTPUT
(1-5V DC LINEAR)
記録計用出力
RECORDER OUTPUT
OFF
LOGGING TEST QUALITY
Humidifier delay control
To protect specimens from condensation, humidity control starts after
temperature reaches the set value.
*ARL, ARS only
OPTIONS
Operation manual
Reports & certificates
?CD
?Booklet
?Testing and inspection report
?Test data
?Temperature (& humidity) uniformity
measurement
?Calibration report
?Calibration certificate
?Traceability system chart
?Traceability certificate
Additional overheat protector
Additional preventive measures can be
taken for excessive temperature rise in
the chamber, in addition to the standard
equipped overheat protector.
Overcool protector
If the temperature inside the chamber
decreases excessively, the chamber
stops operating to prevent the specimens from being damaged.
Trouble buzzer
If a trouble occurs, the buzzer will alert
you of the situation.
Rotating signal lamp
The lamp lights up when alarm triggers.
(Available in red or yellow)
External alarm terminal
If the safety device of the chamber is
activated, the external alarm terminal
will notify it to a remote point.
Emergency stop switch
Stops the chamber immediay.
14
Safety precautions
● Do not use specimens which are explosive or flammable,
or which contain such substances.
To do so could be hazardous, as this may lead to fire or
explosion.
● Do not place corrosive materials in the chamber.
If corrosive substances or liquid is used, the life of the unit
may be significantly shortened specifically because of the
corrosion of stainless steel, resin and silicone materials.
● Do not use living organisms or items that exceed the
allowable heat load as a specimen.
● Be sure to read the operation manual before operation.
Safety precautions
● Do not use specimens which are explosive or flammable, or which contain such
substances.
To do so could be hazardous, as this may lead to fire or explosion.
● Do not place corrosive materials in the chamber.
If corrosive substances or liquid is used, the life of the unit may be significantly
shortened specifically because of the corrosion of stainless steel, resin and silicone
materials.
● Do not use living organisms or items that exceed the allowable heat load as a
specimen.
● Be sure to read the operation manual before operation.
Safety precautions
● Do not use specimens which are explosive or flammable, or which
contain such substances.
To do so could be hazardous, as this may lead to fire or explosion.
● Do not place corrosive materials in the chamber.
If corrosive substances or liquid is used, the life of the unit may be
significantly shortened specifically because of the corrosion of stainless
steel, resin and silicone materials.
● Do not use living organisms or items that exceed the allowable heat
load as a specimen.
● Be sure to read the operation manual before operation.
Please contact us for non-standard specification.
Please contact us for non-standard specification.
Please contact us for non-standard specification.
200V AC, 220V AC spec. 380V AC, 400V AC spec.
OPTION
OPTION
OPTION
OPTION
MODE
MODE
SPECIMEN
TEMPERATURE INPUT
(TYPE T)
試料溫度入力
(JIS T)
POWER SUPPLY
CONTROL
FOR SPECIMEN

No.2
試料電源制御出力
タイムシグナル出力
TIME SIGNALS
ETHERNET
No.6
No.7
No.8
0
No.9
タイムシグナル出力
TIME SIGNALS
外部警報出力
EXTERNAL ALARM
SIGNAL
No.3
No.5
No.4
EXTRA OVERHEAT
PROTECTOR
追加溫度過昇防止器
OVERCOOL PROTECTOR
溫度過冷防止器
槽內溫度
(JIS T
)
モニタ出力 (DC1
-5V リニア)
CHAMBER TEMPERATURE
(TYPE T)
MONITOR OUTPUT
(1-5V DC LINEA
R)
記録計用出力
RECORDER OUTPUT
OFF
OPTION
OPTION
OPTION
OPTION
MODE
MODE
SPECIMEN
TEMPERATURE INPUT
(TYPE T)
試料溫度入力
(JIS T)
POWER SUPPLY
CONTROL
FOR SPECIMEN

No.2
試料電源制御出力
タイムシグナル出力
TIME SIGNALS
ETHERNET
No.6
No.7
No.8
0
No.9
タイムシグナル出力
TIME SIGNALS
外部警報出力
EXTERNAL ALARM
SIGNAL
No.3
No.5
No.4
EXTRA OVERHEAT
PROTECTOR
追加溫度過昇防止器
OVERCOOL PROTECTOR
溫度過冷防止器
槽內溫度
(JIS T)
モニタ出力 (DC1-5V リニア)
CHAMBER TEMPERATURE
(TYPE T)
MONITOR OUTPUT
(1-5V DC LINEAR)
記録計用出力
RECORDER OUTPUT

留言框

  • 產品:

  • 您的單位:

  • 您的姓名:

  • 聯系電話:

  • 常用郵箱:

  • 省份:

  • 詳細地址:

  • 補充說明:

  • 驗證碼:

    請輸入計算結果(填寫阿拉伯數字),如:三加四=7

上一篇:ESPEC GPR-2愛斯佩克高低溫試驗箱

下一篇:ARS-0220愛斯佩克ESPEC高低溫濕熱試驗箱

国产ΑV天堂在线观看免费,经典WC偷窥美女如厕MP4,18禁看,锕锕锕锕锕锕锕好疼免费视频 <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <蜘蛛词>| <文本链> <文本链> <文本链> <文本链> <文本链> <文本链>
掃一掃訪問手機站掃一掃訪問手機站
訪問手機站